Subversion Repositories OpenARM Single-board Computer

# author:       Jelle de Jong <jelledejong@powercraft.nl>
# dist-license: GPLv3
# use-license:  unlimited

#Element[   SFlags  "Desc"  "Name"  "Value" MX      MY      TX  TY  TDir    TScale  TSFlags ]
Element [   ""      ""      ""      ""      1000    1000    0   0   0       100     ""      ]
(
#   Pin [   rX      rY      Thickness   Clearance   Mask    Drill   "Name"  "Number"    SFlags  ]
    Pin [  -9842    0       11811       2000        12012   4331    ""      "1"         0x01    ]
    Pin [   9842    0       11811       2000        12012   4331    ""      "2"         0x01    ]

#   ElementLine [    rX1     rY1     rX2     rY2     Thickness   ]
    ElementLine [   -19685  -15748   19685  -15748   1000        ]
    ElementLine [    19685  -15748   19685   13780   1000        ]
#   ElementLine [    19685   13780  -19685   13780   1000        ]
    ElementLine [   -19685   13780  -19685  -15748   1000        ]

    ElementLine [   -19685   13780  -15748   13780   1000        ]
    ElementLine [   -1969    13780   1969    13780   1000        ]
    ElementLine [    15748   13780   19685   13780   1000        ]

    ElementLine [    -9842  -9842   -9842   -9842    1000        ]
    ElementLine [     9842  -9842    9842   -9842    1000        ]
)

# -----

# x->++

# y
# |
# >
# ++

# -----

# cm to 1000st mill is
# (x/2.54)*1000

# mm to 1000st mill is
# (x*10/2.54)*1000
# or
# x*3937

# -----

# left pin
# X1=5.0/2=-2.5mm = -9842
# Y1=0

# right pin
# X1=5.0/2=2.5mm = 9842
# Y1=0

# Drill
# pin has diameter of 1mm
# 10 % tolarance
# 1.1 mm
# 1.1 = 4331

# Thickness
# pin 1 mm
# 3 x 1mm = 3mm
# 3mm = 11811

# Mask
# 11811 * 1.017 = 12012

# Clearance
# 0.51mm = 2000

# corner up-left
# X1=10/2=-5.0mm = -19685
# Y1=4mm = -15748

# corner up-right
# X1=10/2=5.0mm = 19685
# Y1=4mm = -15748

# corner bottom-right
# X1=10/2=5.0mm = 19685
# Y1=7.5-4=3.5mm = 13780

# corner bottom-left
# X1=10/2=-5.0mm = -19685
# Y1=7.5-4=3.5mm = 13780

# -----

# corner-left
# X1=10/2=5.0mm = -19685

# corner-right
# X1=10/2=5.0mm = 19685

# bottom-left-1
# X1=10/2-1=-4.0mm = -15748

# bottom-right-1
# X1=10/2-1=4.0mm = 15748

# left-center
# X1=10/2-1=-0.5mm = -1969

# right center
# X1=10/2-1=-0.5mm = 1969

# -----

# spot left
# X1=5.0/2=-2.5mm = -9842
# Y1=7.5-4-1=2.5mm = -9842

# spot right
# X1=5.0/2=2.5mm = 9842
# Y1=7.5-4-1=2.5mm = -9842